Modern Christmas Tree Planter
I like the fashionable twist to a standard Christmas tree planter field with horizontal slats and clear traces. It’s a breath of contemporary air out of your typical vacation decor. Bonus – these are extraordinarily sturdy/heavy weight, so that they’ll final year-round!
Below you will see the step-by-step directions to create this contemporary Christmas tree planter.
- (1) Four X 8 Plywood Sheet @ ¾-in.
- (15) 1 X 2 @ 8-ft
- (1) 2 X 2 @ 8-ft
- 120/220 Grit Sand Paper
- 1-1/Four in Kreg Jig Pocket Hole Screws
- 1-3/Four in Brad Nails
- Safety Glasses
- Paint Stir Stick
- Circular Saw or Table Saw
- Miter Saw
- Kreg Jig
- Brad Nailer
- Measuring Tape and Pencil
CUT LIST (FOR TWO PLANTERS)
- Four X 8 – ¾ in Plywood Sheet
- (2) 19 in. W x Eight FT
- (8) 15 ¾ in X 19 in
- (2) 15 ¾ in X 17 ¾ in
- (15) 1 X 2 @ 17 3/Eight in
- (8) 2 X 2 @ 2 in
- Optional: Fit left over 1 X 2 scraps to prime at 45-degree mitered cuts
Using a round noticed or desk noticed, rip your Four X Eight plywood sheet to 19 in W X Eight ft L. If you don’t personal a noticed, an affiliate at The Home Depot will be capable of rip it for you!
Using a round noticed or a desk noticed, rip your 19 in X Eight ft items into (4) 19 in X 15 ¾” in items for the planter field sides.
When measuring, make sure to examine if every little thing is sq.!
With the left-over items of plywood, use a round noticed or desk noticed to chop the planter field bases at 15 ¾ in X 17 ¾ in.
Use a miter noticed to chop your slats for each aspect. Each planter is just overlaying three sides because the again of the planter is not going to be viable. Cut (15) 1 X 2 @ 17 3/Eight in to offer you a grand whole of (72) 17 3/Eight in items.
Once your entire cuts have been made its time to assemble the Christmas tree planter bins! Below reveals the cuts for one planter field. Remember, we’re solely overlaying three sides with horizontal slats.
Use a drill and a Kreg Jig to make Four pocket holes screws on 2/Four planter field sides.
Make two holes on the prime and two on the backside. Do not put pocket holes in the entire sides, you solely must in two boards per planter field.
Use two clamps to maintain the boards flush and in place. Take your drill and 1 ¼ in pocket gap screws to connect the pocket gap board to the NON-pocket gap board.
Repeat this course of on the opposite aspect by flipping the “U-shape” onto the second pocket gap board and fix Four pocket gap screws.
Use a brad nailer and clamps to connect the bottom to the underside of the planter. Use not less than Eight nails within the corners and center, use extra if desired for further safety.
Attach your slats beginning on the prime of the field through the use of wooden glue and two small clamps to carry in place. Use a brad nailer to safe a nail on every finish.
Use a paint stir stick as a spacer between every slat. Glue and brad nail all 12 slats and repeat these steps until all three sides are accomplished.
(Optional) Use the scraps out of your 1 X 2’s and minimize 45-degree mitered corners for a completed look on the highest of the planter. Secure with wooden glue and brad nails.
Cut (4) 2 X 2 @ 2 in and fix the legs to the underside of the planter utilizing wooden glue.
Use 120 and 220 Grit sand paper for a easy end on the tops and sides.
The planters have been an ideal addition to modernize our entrance porch for Christmas. I completed the DIY Christmas Tree Planters off with vacation decor from The Home Depot. Believe it or not, all of the greenery is fake right here! There have been so many practical bushes, wreaths and garland with built-in lights and timers. All of the decor, together with the items and pink truck, have built-in battery operated lights and timers so there aren’t cords all around the porch!
Get the Look
- Planter Trees
- Vine Gift Boxes
- Metal Red Truck
- Coir Door Mat
The put up Modern Christmas Tree Planter appeared first on The Home Depot Blog.
Original supply: https://blog.homedepot.com/modern-christmas-tree-planter/