Decorative moulding on the entrance of a tub provides an instantaneous facelift to an outdated tub and actually improves the general look a WC. Read on to see the complete tutorial on easy methods to simply add moulding to a tub and provides it the makeover it wants!
Step 1: Prep
Using a putty knife, hammer, and pry bar, take away all current trim or moulding items from the floor of the tub that you don’t plan to make use of for this undertaking. Make certain to additionally take away any baseboards that sit flush with the entrance of your bathtub and will get in the best way of making use of the brand new moulding (non-obligatory aspect notice – save these baseboards for later as they might be reused once more throughout Step 8). Clean the floor space of your bathtub effectively to take away all mud, stains, paint drips, and/or previous glue on the floor of your tub the place the brand new moulding will go. This is to make sure that the glue adheres to the tub correctly.
Step 2: Tile Board
Measure the floor space of the place your tile board goes to go. Cut the tile board in keeping with your measurements utilizing an oscillating multi-tool. Glue the tile board on the flat floor of your tub utilizing Loctite Power Grab glue and a caulk gun. Spread a complete tube of the Loctite Power Grab glue evenly on the again of the tile board earlier than urgent it to the floor of your tub. Reinforce the tile board in place to forestall sagging through the use of clamps if relevant. If clamps don’t match on the configuration of your bathtub, use heavy items of furnishings or scrap items of wooden laying round to safe the tile board in place. Let treatment for 24 hours. Pro tip – place a bit of scrap wooden in between the tile board and clamp to carry in place and permit clamp to suit over the tub. (see picture).
Step 3: Measure and Cut Vinyl Moulding
Using the measurements of your bathtub mixed with the scale of the vinyl moulding, draw out a diagram of how your bathtub goes to look. This will mean you can decide how lengthy each bit of vinyl moulding must be and the place to make your cuts. Cut six vinyl moulding items in keeping with your measurements utilizing a miter noticed (see diagram above labeled with stars). Suggestion: lower one piece at a time and ensure it suits in place incase your bathtub just isn’t completely degree. You may have to return and make some minor changes. I had to do that just a few occasions with just a few items as our bathtub had settled erratically. Measure twice, lower as soon as!
Step 4: Glue Vinyl Moulding
Glue each bit of lower vinyl moulding to the tile board so as to create the three-panel design. (see picture). Secure the moulding items in place utilizing clamps and/or further items of wooden.
Step 5: Measure, Cut, & Glue Interior Trim
Measure 4 inside sides of rectangles created by vinyl moulding to complete out with trim (see picture). Cut trim items in keeping with measurements.
Step 6: Caulk
Caulk any cracks that stay utilizing Silicone caulk. This will be sure that water doesn’t seep in behind the moulding.
Step 7: Paint
Apply one coat of Kilz Primer over moulding space. Let dry. Apply one coat of Behr Urethane Alkyd Semi-Gloss Enamel paint in a fascinating colour over primer and let dry. Apply a second coat of paint if essential.
Step 8: Add Back Baseboards (Optional)
Glue again any baseboards that had been eliminated throughout step 1, if essential. This step is “optional” as a result of, relying on the dimensions of your tub and surrounding partitions. There might not be room left for previous baseboards as a result of new moulding added to the bathtub. If baseboards are added again to the encompassing partitions, paint to match the brand new bathtub moulding.
Now you’ll be able to stand again to admire your superbly new up to date bathtub.
The put up How to Add Decorative Moulding to a Bathtub appeared first on The Home Depot Blog.
Original supply: https://blog.homedepot.com/how-to-add-decorative-moulding-to-a-bathtub/