The following directions will stroll you thru creating this lovely, farm-house styled desk with an superior brown-gray stain end!
Cut Wood Pieces for Table Frame and Top
We will begin by reducing down the wooden items to dimension for assembling the desk body. The chart within the picture exhibits the sizes of wooden that every piece of wooden must be lower all the way down to. To lower the items of wooden, all you want is a hand round noticed, however you should use a miter noticed and a desk noticed as effectively you probably have them!
Cut Slots within the Leg Posts
Use a round noticed or desk noticed to chop out 3.5” broad slots 1.5” deep in every of the leg posts (Part D) 6” from the underside of the posts. Use a chisel to chop out any wooden left over within the corners and make sure the helps will match snugly afterward.
Attach the Frame Pieces
Attach the leg backside outer slats (Part E) and leg higher aspect slates – quick finish (Part H) to the leg posts (Part D) to create the 2 aspect items. The backside aspect slats ought to match into the underside slots you beforehand lower. The high aspect slats must be lined up with the highest of the leg posts. Use a mix of pocket screws and wooden glue or your most well-liked joinery technique to connect the highest slats. And simply wooden glue for attaching the underside slats into the cut-out slots.
Cut Slot for Bottom Middle Support Slat
Use both a hand round noticed or a desk noticed with a dado blade to chop out the center slots within the aspect body items. The center slot must be 3.5” broad and 1.5” deep and must be 13” in from every submit.
Attach Center Slats
Use a mix of pocket screws and wooden glue (or a joinery technique of your alternative) to connect the wooden slats on the highest and backside of the desk. For the highest slats, you possibly can select to both have the slats aligned with the outer or interior fringe of the desk, primarily based on the design you like. In this construct, I hooked up the highest slats on the interior edge in order that they might not be seen with the top product. The high slats must be hooked up flat with the highest of the leg posts. The backside heart slat ought to match snugly into the underside heart slot lower out within the earlier step.
Attach Table Top Pieces
Attach the desk high items (Parts B and C) utilizing a mix of pocket screws and wooden glue. You can select to make use of any joinery technique for this half however be sure that every bit is flat on either side and hooked up in order that the highest of the desk can be flat.
Attach End Pieces to Table Top
After attaching the seven items of wooden to make the width of the desk, connect the 2 finish items (Part A). This is an elective step to make the desk longer. Just be certain as you probably did within the earlier step that the top items are flat on the highest with the remainder of the desk. You can use pocket screws and wooden glue as seen right here or a joinery technique of your selecting!
Cover Pocket Holes
If you selected to make use of pocket holes for the joinery, be certain to plug the holes with dowel rods and use a flat pull noticed to make them flush with the wooden!
Paint Base Coat and Stain Finish Combination
For the desk high, add a white wash paint combination as a base coat. Then combine a bottle of half white wash with half Varathane darkish walnut wooden stain and apply this to the whole desk. This offers it an superior mild grey/brown coating as seen within the photos. For the remainder of the desk helps, simply use the white wash paint to provide the desk some good distinction.
Attach the Table Top to the Frame
Attach the desk high to the desk body. Use proper angle brackets to be able to take away the desk high if want be sooner or later. Make certain that the highest sits heart on the body.
Apply Several Coating of Polycrylic
After the entire portray and marking has dried, apply a number of layers of Shellac Finish and Sealer. For this desk, I used a complete of seven layers. This ensures that the desk gained’t soak up water over time and can be stain resistant and simple to scrub!
Sand the Table with High Grit Sandpaper
The remaining step is to easy out the whole desk with a collection of sandpaper. Start with a 300-grit paper and work your approach as much as 4000-grit paper and a few ending pads. This will give the desk a glass-like end that can be easy to the contact!
Our Farmhouse Dining Table
Original supply: https://blog.homedepot.com/diy-farmhouse-dining-table/